Setting tappet clearances on a Blackstone SS engine

Setting tappet clearances on a Blackstone SS engine is a job of measurement, not adjustment by feel. The tappet, often called a valve lifter, carries the pushrod load against a rocker arm. The working gap forms part of the lash in the valve train: it lets the valve close fully while keeping the mechanism free and quiet. A wrong setting can reduce compression, upset valve timing and, over time, damage the valve seats and faces.

An SS in an Australian shed may have spent years dusty, rain-stained or stored beside modern farm machinery. Collectors often call it “the old SS,” a useful reminder that engine badges and type codes can become muddled during rebuilds. Such machines may turn up at country auctions around Wagga Wagga or Tamworth, or in inner-Melbourne salvage yards, sometimes with the original valve-gear covers still fitted and the specification papers missing.

The adjustment itself is straightforward once the correct reference figures are known. Position each cylinder at compression top dead centre, measure the gap between the tappet face and rocker arm, then alter the adjuster by very small amounts. The important part is resisting the temptation to copy a clearance from another engine. Tappet clearances are measured in thousandths of an inch or in millimetres, and the factory value for the particular SS configuration should govern.

Before any work begins, isolate the fuel and ignition systems, disconnect the battery and allow hot manifolds and exhaust passages to cool. Support the cylinder head when it is removed, and use a hand barring or crank arrangement rather than starting the engine in the workshop. Keep eyes and hands clear of the exposed valve gear. A measured adjustment on a stationary engine is safe, methodical work and rarely needs rush.

Identify the engine and find the correct specification

Identify the engine before touching an adjuster. Look for the maker’s name, serial number, cylinder count and any stamped or cast identifiers around the crankcase, rocker box and cylinder head. Note the original finish and the arrangement of the inlet and exhaust rockers. These details prevent a replacement screw or head gasket from being fitted to a superficially similar SS from another production period.

The SS code sits within the family of R. A. Lister type designations, so a guide to the various Lister type designations is useful when checking a plate, casting or preserved catalogue entry. The code should be matched to the engine’s actual construction rather than treated as a model name on its own. Pattern numbers can identify a production batch, while the mechanical layout determines what the service manual actually covers.

Search the original workshop book, owner’s papers and any hand-written notes before consulting a general mechanic’s rule of thumb. If the engine still runs, measure and record its present clearance before dismantling; that gives a baseline, although wear can make an old setting misleading. Australian workshops often mix metric decimal values with imperial feeler gauges in thousandths; 0.001 inch equals 0.0254 millimetres. Record both units and the original adjustment hardware. British Standard Whitworth threads are common on vintage British machinery, whereas locally sourced replacement fasteners may be UNC or UNF, so record the thread pitch too.

Prepare the engine safely and clean the valve gear

Isolate the engine mechanically as well as electrically. Close the fuel cock, disconnect the starter and battery leads, and identify any hot-bulb or electrical ignition components before moving them. Relieve cylinder pressure and coolant pressure where applicable. If the engine has been running hot, leave it long enough for the head, valve faces and exhaust to cool; thermal expansion can change a clearance reading.

Remove the cylinder head or rocker cover according to the engine’s layout, supporting the head and catching coolant or oil. Clean carbon from the combustion chamber, valve faces, tappet crowns and the bearing points of the rockers. A bright valve face and a clean tappet make a steady reading much easier. Use a soft brush and degreaser, but keep solvent away from oiler reservoirs and open bearings.

Inspect the pushrods, tappets, rocker faces and adjuster threads for wear, burrs and distortion. Replace a scored tappet or damaged rocker bearing rather than compensating with an excessive clearance. Australian sheds often see hard summer heat, winter damp and wind-blown dust combine on an open verandah, so check for corrosion and swollen oil wicks as well as obvious rubbing marks.

Locate compression top dead centre

Remove the spark plug or injector opening so that piston movement can be seen, and clean the chamber walls if deposits hide the piston crown. Rotate the engine slowly by hand in the normal running direction. Watch the inlet and exhaust valves as the piston approaches the highest point, and identify the position at which both valves are closed and the piston is about to move downwards.

A temporary chalk or pencil mark on the flywheel can preserve the selected position. If the original timing marks have vanished, do not assume that the nearest visible crank position is correct. Valve overlap may mean that neither valve is fully closed at the exact crankshaft TDC, so use the engine’s specified timing method and distinguish the compression stroke from the suction stroke before measuring.

With the cylinder held at compression top dead centre, the tappets should be fully down and the rockers should be at the closed-valve position. Check that no pushrod is being held off its cam by a lobe, and that both valve faces sit cleanly on their seats without a valve hanging open. Repeat the procedure for every cylinder, recording the flywheel position for each rather than assuming the firing intervals are equal.

Measure and adjust the tappet clearances

Place a feeler gauge of the chosen thickness between the flat tappet face and the underside of the rocker arm. Push it down gently and find the largest blade that still slides with light resistance. The reading is the tappet clearance; do not measure between a pushrod and tappet, as that is a different part of the valve train. Test inlet and exhaust rockers separately and keep the engine at the same reference position.

If clearance is too small, screw the adjuster in slightly; if it is too large, back the adjuster out. Hold the adjuster while tightening its locknut, then repeat the measurement because the locknut can move the setting. Work in very small increments and use the specified feeler gauge rather than forcing a thick blade into the gap. Do not straighten a bent rocker with force or substitute a shim unless that is the original design.

If the required figure is unavailable, have the engine’s geometry checked before altering anything. When a replacement adjuster, thread gauge or missing dimension must be sourced, an engineering and sales dialogue can prevent vague descriptions and make sure the supplier receives usable information. In Australia, posting a small part from Melbourne to Townsville can cost more than the component, so a local engineering shop may reproduce a damaged screw while preserving its original length, head and thread.

Reassemble and prove the valve timing

Reassemble with the correct head gasket, tighten the cylinder head studs evenly and to the specified torque or firmness. Refit the rocker shaft and adjusters, then check that no adjuster has been rotated during assembly. Restore the oil supply and any coolant, and turn the engine over by hand once more. The mechanism should move freely without a valve touching its seat, and no adjuster should show fresh thread damage.

Start the engine without load and listen for irregular valve noise, check oil pressure or visible oil flow and watch for smoke from an imperfectly seated valve. Then run it at a steady working speed long enough for the valve gear to settle. Correct valve timing and ignition or fuel settings still need attention after the mechanical lash has been set. A tappet clearance that is too tight can leave a valve fractionally open and promote carbon and burned faces.

Recheck the clearance after the first run with the engine cold and the mechanism in the same mechanical position used for adjustment. A reading may change slightly as oil films settle or parts acquire heat, but a large change indicates that something has shifted. Keep the cylinder order, original shims, reused washers and every replaced component clearly marked. Record the final inlet and exhaust figures, the make of gauge used and the date, then compare them at the next service.


Keeping a Blackstone SS in working order preserves more than an engine: it keeps a pattern of mechanical knowledge alive for the next owner. Make a dated record of the original settings, photograph the adjuster position, and note every washer, shim, screw and gasket removed. Where a plate has been lost or a hand-written note is hard to read, preserve it with the engine’s history rather than discarding it during a tidy rebuild. If you can add useful photographs, measurements or documents to the archive, pass them to Peter and Rita for inclusion in the site’s growing record of engines, machinery and overseas travel reports. Share the result with fellow stationary-engine enthusiasts, record the before-and-after figures, and leave the old SS ready for its next day in the shed.