Lister E and F engines: a technical comparison

The Lister E and Lister F engines occupy an important part of Britain’s stationary diesel tradition. Both are compact, vertical single-cylinder machines, but the F was developed with greater capacity and output than the E. Their simple layout made them useful on farms, in workshops and at remote power installations, and many reached Australia through the country’s close commercial links with Britain.

A useful comparison depends on more than the letter stamped on the crankcase. Production dates, ratings, cylinder dimensions and starting arrangements changed within each model family. Australian owners should therefore treat catalogue specifications as guides, then use the engine’s data plate, physical measurements and surviving paperwork to establish its individual identity.

Origins and model identity

Lister engines were built during a complex period of British industrial consolidation, so surviving machines may carry names associated with different companies within the same manufacturing lineage. The letter itself does not provide a precise year. An E can represent several revisions, while an F may have been supplied for pumping, sawmilling, generation or general stationary work with different auxiliary equipment.

Records are especially valuable when letters are easily confused in auction catalogues and faded paint. The Lister A register provides a useful example of this approach because it records known machines individually instead of treating every engine of a given type as mechanically identical. Similar registers can reveal production patterns, surviving variants and details that would otherwise be lost.

The maker’s plate should be photographed before any cleaning or dismantling work. Record the serial number, stated horsepower, rated speed and any supplier’s name. Compression ratio, injector type, fuel-pump arrangement and lubrication method can distinguish revisions that otherwise appear to carry the same letter.

Core mechanical layout

Both engines are normally four-stroke diesels with one vertical cylinder, a substantial flywheel and a mechanical governor. The common catalogue figures place the E near a 5-inch bore and 6-inch stroke, while the F is commonly listed with a bore around 6 inches and a stroke of about 7½ inches. Those dimensions are approximately 127 by 152 millimetres for the E and 152 by 190 millimetres for the F.

The smaller E has a more compact bed, cylinder and flywheel. This makes it easier to handle in a farm shed and generally gives quicker warm-up characteristics. Its smaller rotating mass also suits lighter belt-driven equipment, although the engine still has enough inertia to smooth the firing intervals of a slow-speed single-cylinder power cycle.

The F requires a larger bed and flywheel to control the greater combustion forces. Its increased cylinder dimensions produce more torque and require a fuel system capable of delivering a larger charge. The F was not simply an enlarged E: cooling arrangements, starting provisions and auxiliary components also differ between examples.

Combustion, starting and fuel

A four-stroke cycle governs the engine’s working rhythm: induction, compression, power and exhaust. Hot-bulb combustion was common in the earlier Listers, including surviving E and F examples. A small pilot charge heats a separate bulb, and compressed air carries the prepared mixture into the main chamber. Later production changes and replacement components mean the original arrangement should be confirmed rather than assumed.

The smaller E was often fitted with rope or hand starting, with operation depending on access to the flywheel. F engines were more likely to receive compressed-air assistance because of their greater mass and compression. Some Australian machines have been converted to electric starting, making the original layout harder to see unless those alterations are documented.

Mechanical injectors and high-pressure pumps supply fuel, while the governor regulates delivery according to load. The exact linkage can differ between a simple hit-and-miss governor and a more elaborate speed-control arrangement. Some engines also have a separate starting-fuel system. Fuel-line markings, pump settings and workshop notes are therefore more valuable than a general claim that the engine “runs on diesel”.

Performance and working applications

Published ratings commonly describe the E as an engine of roughly 6 to 8 horsepower and the F as approximately 10 to 12 horsepower. These figures are not perfectly interchangeable: some are quoted at the crankshaft, some represent brake output, and rated speeds vary. At the usual speed of about 500 revolutions per minute, the E produces around 4½ to 6 kilowatts, while the F is commonly placed between 7½ and 9 kilowatts.

Neither engine is designed for high-speed transport work. Their strength lies in low-speed torque, steady belt drive and the ability to run for long periods on a controlled fuel supply. An E can suit a small pump, chaff cutter, workshop machine or compact generating set. The greater output of an F allows it to drive larger pumps, sawmills, crushing equipment, mixers or a more substantial alternator.

Australia gave these engines roles that are now associated with electric motors. Before reliable grid electricity reached many farms, a Lister could operate a dairy, grain mill, irrigation pump or village workshop. The E was particularly useful where a full-size F would have been excessive; the F suited heavier seasonal work and machines requiring greater torque during startup.

Cooling, lubrication and endurance

Water cooling is one of the most visible differences in operating demands. An open hopper-and-tank system is common on small Listers, while larger or later machines may use a more enclosed arrangement. The F has greater cooling requirements because it releases more heat from a larger cylinder. Restricted passages, a damaged pump or a failing thermostat can quickly turn a cooling problem into an overheating failure.

Lubrication arrangements vary between production periods. Drip-feed systems, in which oil is directed to critical points, appear on many stationary engines; later examples may use a more automatic arrangement. Oil passages, pump drives and oilways should be identified before dismantling. Keeping the original lubrication method is valuable, but worn bearings and distorted components require rebuilding rather than simply reconnecting the old pipework.

Australian conditions make careful preparation important. A shed at Orange or Bathurst can face summer heat, dust and unreliable water quality. Farm dam water may carry sediment, while coastal water in Queensland can encourage scale or biological fouling. Suitable coolant, clean strainers and regular flushing matter more than merely filling the tank and assuming the system will remain protected.

Condition checks and useful records

A compression test is a useful starting point, but it should be combined with an examination of the cylinder, valves, injector and fuel system. On a single-cylinder engine, uneven running may point to a mechanical fault rather than a carburation-like mixture problem. Excessive smoke also needs interpretation: oil smoke, unburned fuel and steam carry different meanings.

Measured records make an engine’s history more valuable than subjective descriptions. A consistent log can include compression readings, oil consumption, coolant condition, fuel delivery settings and the speed at which the governor holds. Fluid condition benefits from the same discipline. Modern environmental work uses optical backscatter measurements to estimate sediment flux in estuarine water. A comparable turbidity trend for cooling water can flag sediment or biological fouling, although it cannot diagnose internal engine wear.

Restoration records should include photographs before dismantling, measurements of modified components and notes on what was replaced. Even a minor observation, such as a non-original starter or a later fuel line, may help another owner distinguish an original arrangement from a sympathetic restoration.

Keeping these engines working in Australia

Buying and moving an old Lister is rarely a simple local transaction. Machines appear at rural auctions, farm sales, swap meets and specialist dealers around Geelong, Ballarat, Bendigo, Charters Towers and regional New South Wales. Private sales can be less formal, with a barn or farm shed serving as the inspection area. Museums, historical societies and vintage machinery clubs often hold the best local knowledge, even when they do not own the particular engine being examined.

Distance affects every restoration. A replacement component may travel from another state in a ute, while a complete engine may need a crane, specialist crate and insured transport. Australian workshops routinely encounter British imperial fasteners beside modern metric equipment, so the correct spanner, thread gauge and clearance can be harder to find than the component itself. Local trade speech may be informal, but terms such as starter, compression and injector remain recognisably British.

Locate the oldest Lister within your own property or community, photograph its maker’s plate, and record its serial number, bore, stroke and fuel system. Share verified details with a historical society, museum or stationary-engine register. Run it safely, preserve the evidence and pass the information onward, ensuring these working machines retain both their history and their place in the Australian landscape.